Battery Relocation Tray

3.4L (5VZ-FE) Conversion LH Battery Relocation Tray

Installation notes This tray is delivered un-painted and is constructed of mild steel. We recommend painting this tray prior to installation. Remove the air intake box, washer bottle, and any other restrictions in LH front corner of the engine bay. Set the ORS Battery Relocation Tray in this corner. Using the washer bottle (will be […]

Continue reading
ORS High Pressure Fuel Hose

3.4L (5VZ-FE) Conversion High Pressure Fuel Hose

Installation notes For 3VZ-E and 22R-E models Note: The original 22R-E or 3.0L fuel pump (in-tank) normally works well with the 3.4l engine and can be left in place. However, if a supercharger is used, ORS recommends upgrading to a performance fuel pump. Also, be sure to purge fuel hose w/ compressed air before installation. […]

Continue reading
PS hose installed at pump on ABS model

3.4L (5VZ-FE) Conversion Power Steering Hose

Installation Notes Install one adapter into the steering gear or the ABS actuator (if equipped). If using the ABS actuator, the provided gasket is installed between the adapter and the ABS actuator as a seal. If installing the adapter into the steering gear, be sure the gold-colored compression fitting is in place, inside the steering […]

Continue reading
ORS Conversion Harness Layout - '85-'88 22R-E Recipient Applications

Conversion Wiring Harness – 3.4L (5VZ-FE) and 2.7L (3RZ-FE)

Install Instructions Conversion Wiring Harness, 85-95 22R-E and 3VZ-E applications 3.4L 5VZ-FE & 2.7L 3RZ-FE Engines *****NOTICE TO CUSTOMER: If there is a problem suspected with the wiring harness, call ORS. DO NOT cut, alter, or dissect the ORS conversion harness. ORS accepts no responsibility for a harness that has been tampered with. If wire […]

Continue reading
ORS Conversion Harness Layout - '85-'88 22R-E Recipient Applications

Stand-Alone Wiring Harness – 3.4L (5VZ-FE) and 2.7L (3RZ-FE)

Standalone Wiring Harness Installation Instructions 3.4L 5VZ-FE and 2.7L 3RZ-FE applications *****NOTICE TO CUSTOMER: If there is a problem suspected with the wiring harness, call ORS. DO NOT cut, alter, or dissect the ORS conversion harness. ORS accepts no responsibility for a harness that has been tampered with. Please read all instructions before beginning work. […]

Continue reading
Rear Long Travel Shock Mount

Rear Long Travel Shock Hoop: ’79-’95 Truck/4Runner

NOTES: Be sure to read and fully understand these instructions before starting the installation process. These hoops are designed to run a shock with about 13” of travel on a vehicle with approximately 3-7” of lift. Proper shock length is determined by spring travel, vehicle use, and the placement of the bumpstops relative to ride […]

Continue reading
Rear Long Travel Shock Mount

Rear Long Travel Shock Hoop: ’95-’04 Tacoma

NOTES: Be sure to read and fully understand these instructions before starting the installation process. These hoops are designed to run a shock with about 13” of travel on a vehicle with approximately 3-7” of lift. Proper shock length is determined by spring travel, vehicle use, and the placement of the bumpstops relative to ride […]

Continue reading
Rear Long Travel Shock Mount

Rear Long Travel Shock Hoop: ’99-’06 Tundra

NOTES: Be sure to read and fully understand these instructions before starting the installation process. These hoops are designed to run a shock with about 12-14” of travel on a vehicle with approximately 3-7” of lift. Proper shock length is determined by spring travel, vehicle use, and the placement of the bump-stops relative to ride […]

Continue reading