FROR SAS Kit

Front Range Off-Road SAS Kit

  Remove all the IFS brackets, being careful around the motor mounts, as they will likely need reinforcement. Assemble the supplied jig, bolting it together with the ¼” bolts. When assembled, the 18mm holes, center to center is 43.5”. The “hook” end of the jig is used at the rear, to get around the body […]

Continue reading
Tacoma In-Cab Cage Kit

Tacoma In-Cab Cage Kit (Non-Assembled)

ORS-CA010 ‘95-’04 Tacoma X-cab Congratulations on your purchase! IMPORTANT: Please read ALL instructions completely before beginning. The customer is responsible for the fit and finish of this product. The customer is also responsible for informing ORS of any and all problems BEFORE beginning installation. The installation of this kit requires fabrication and welding skills. The […]

Continue reading
22R and 22RE Performance Engine Mounts

22R and 22RE Performance Engine Mounts (ORS-EC010)

ORS-EC010 This kit should include the following: 1 x Driver side mount 1 x Passenger side mount 4 x 2” polyurethane bushing 2 x Machined bushing sleeve 2 x 5/8” x 4.5” Bolt 4 x 5/8” Flat washer 2 x 5/8” Lock washer 2 x 5/8” Nut   The fit of the engine in the […]

Continue reading
Diagnostic Connectors

22R Fuel Injection Conversion Harness Cores

CORE CONNECTORS LIST FOR ORS-EC002 ’85-’88 22R-E Conversion Harness There are 7-10 core connectors needed from the customer for this harness. All these connectors are all found in the “body” or “dash” harness of the donor (EFI) vehicle. When cutting these connectors please leave at least 4” of wire lead intact. All applications: The ECU […]

Continue reading
Fuel Injection Conversion Harness

22R Fuel Injection Conversion Harness (ORS-EC002)

ORS-EC002 ’85-’88 Minitruck & ’85-’89 4Runner Donor Fuel Injection *****NOTICE TO CUSTOMER: If there is a problem suspected with the wiring harness, call ORS. DO NOT cut, alter, or dissect the ORS conversion harness. Off Road Solutions accepts no responsibility for a harness that has been tampered with – NO EXCETPIONS. There are cores needed […]

Continue reading
Fuel Injection Conversion Harness

22R Fuel Injection Conversion Harness (ORS-EC001)

ORS-EC001 ’89-’95 Minitruck & ’90-’95 4Runner Donor Fuel Injection *****NOTICE TO CUSTOMER: If there is a problem suspected with the wiring harness, call Off Road Solutions. DO NOT cut, alter, or dissect the ORS conversion harness. Off Road Solutions accepts no responsibility for a harness that has been tampered with – NO EXCETPIONS. Off Road […]

Continue reading
Manual Hub Conversion

Manual Hub Conversion Kit (Basic Kit)

ORS-HB051/HB052/HB053 NOTICE: It is highly recommended that a qualified technician install this kit. Special tools/equipment are required for the installation. Experience with these procedures, particularly pressing wheel bearings, is highly recommended. Improper installation will void the warranty on these parts; this is the responsibility of whoever purchases this kit. This kit does not include lockouts […]

Continue reading
Manual Hub Conversion

Manual Hub Conversion Kit

ORS-HB001/HB002/HB003 NOTICE: It is highly recommended that a qualified technician install this kit. Special tools/equipment are required for the installation. Experience with these procedures, particularly pressing wheel bearings, is highly recommended. Improper installation will void the warranty on these parts; this is the responsibility of whoever purchases this kit. NOTICE TO CUSTOMERS USING A LIFT […]

Continue reading
High Angle CV Boot Kit

High Angle CV Boot Kit (ORS-HB201)

Thank you for purchasing our High Angle CV Boot Kit! Notice to customer: There is no warranty on the ORS High Angle CV Boot Kit. This High Angle CV Boot Kit is designed to reduce CV boot wear in high angle situations. This part is not designed to fit in the same manner as the […]

Continue reading